R&D SERVICES

DSP, SDR and FPGA development

We build signal-processing systems end to end: the algorithm, a bit-exact model you can run in a browser, the RTL and firmware, and the measurements on real hardware.

01

What we build

DSP algorithms

Filters, demodulators and synchronisation; radar processing (matched filtering, CFAR, range-Doppler); TDOA/FDOA geolocation; LoRa/CSS and other modems. Floating point first, then fixed point, bit for bit.

FPGA and RTL

Verilog DSP blocks with fixed-point models that match the hardware bit for bit, formal verification and area budgets. Zynq-7000, JESD204B, AD9361 and ADRV9009 designs.

SDR firmware and bring-up

Board bring-up, Vivado and PetaLinux builds from source, custom transceiver profiles, DMA and data-path debugging, libiio and pyadi-iio tooling.

Browser-native SDR

WebUSB drivers that stream an SDR straight into a web page with nothing to install: live spectrum, demodulation and instruments for the lab or the field.

Digital twins and simulation

Models of the radio, the channel and the scene, to test a design before the hardware exists, with Monte Carlo runs checked against theoretical bounds.

Productisation

Hardware reverse-engineering from schematics, device licensing and secure boot, firmware packaging, and 3D-printed RF enclosures.

02

Selected work

Every number below is a recorded measurement from the bench or a test run.

Zynq-7100 · ADRV9009 · JESD204B

Wideband ADRV9009 bring-up

Took a 100 MHz baseline to 200 MHz full duplex by deriving new transceiver profiles and fixing the clocking, framer and transceiver-PLL issues on the way.

200 MHz
full-duplex bandwidth, from 100 MHz
245.76 MS/s
each way, on 9.83 Gb/s lanes
450 MHz
transmit bandwidth, experimental
Vivado 2022.2 · PetaLinux · ADI HDL

Reproducible firmware from a GUI-only project

The board's published build scripts targeted a different evaluation board, and the real changes lived only in a GUI project. We wrote them back into scripts, so the firmware rebuilds from source and matches the shipped design.

95 / 95
IP blocks match the shipped design
0 errors
PRBS on all 3 JESD204B links
39 min
full rebuild, FPGA and Linux
ADRV9009 · AXI DMA

Fixing an arbitrary-waveform transmit path

Arbitrary waveforms came out in short bursts every few seconds. We ruled out the data, power, buffers and RF path one at a time, traced the fault to the firmware and fixed it with the rebuild.

13 / 13
captures with signal, from 3 / 13
0.999
chirp correlation, from 0.003
Fobos SDR · WebUSB · Rust · TypeScript

SDR streaming into the browser

A WebUSB path that streams a 14-bit, 50 MHz SDR straight into a web page, plus a native bridge for browsers without WebUSB.

199 MB/s
sustained over USB, 0 errors
≈ 50 MS/s
into the page
39 ms
retune
numpy · Rust · Verilog

Bit-exact FPGA DSP

A CIC decimator written as one design in three languages, each run against the same test vectors, so the FPGA output matches the model bit for bit before it reaches silicon.

60 / 60
reference self-tests
25 / 25
Rust model tests
22
Verilog vector runs, bit-exact
Zynq-7020 · AD9361 · OpenSCAD

SDR board reverse-engineering

A schematic-level reference for a Pluto-class 2R2T board (FPGA resources, clock accuracy, RF chain) and a parametric 3D-printed card cage for four boards.

0.5 ppm
reference clock: ±1.2 kHz at 2.4 GHz
115×135×103 mm
four-board cage, 111 g
03

How we work

  1. 01

    Describe the task

    Send the form below. We reply within two business days with questions or an offer of a short call.

    Start here →
  2. 02

    Feasibility study

    A short, fixed-scope study: what is possible on your hardware, the numbers, the risks and a plan.

    → plan, numbers, risks
  3. 03

    Model first

    A bit-exact model or digital twin you can run and tune in the browser before any hardware is built.

    → bit-exact model
  4. 04

    Build and measure

    RTL, firmware and software, verified on the bench. You get recorded measurements, not screenshots.

    → recorded measurements
  5. 05

    Hand over

    Source, build scripts, test vectors and reports, so your team can rebuild and extend the work.

    → source + build scripts
04

In-house hardware platforms

  • Zynq-7020 + AD9361
    2R2T
  • Zynq-7100 + ADRV9009
    JESD204B
  • PlutoSDR-class boards
    AD936x
  • Fobos SDR
    14-bit · 50 MHz
  • Digilent Nexys A7
    Artix-7
05

Questions

Do you sign NDAs?

Yes. Tick the NDA box in the form and we will sign one before you share any details.

Where are you based?

In Ukraine. We work remotely with clients anywhere, in English or Ukrainian.

Do you take defence or dual-use projects?

Yes, under contract and within the applicable export-control rules.

Can you work on our hardware?

Yes, and the board can stay with you. You plug it into your computer and open a page we host, which connects to it over WebUSB or WebSerial, and we work on it remotely from there. That is also how we onboard a new board. If you prefer, send us one, or we start on ours and port the work to yours.

06

Describe your task

The more specific, the better: signals, rates, hardware, and what “done” looks like.

your_task sink · waiting
Areas
Stage · timeline · budget

Received